CA LIC #756210

Our License Number

(408) 679-5820

Give Us a Call

How to Maintain Your Water Heater?

This article is a simple water heater maintenance procedure so that it can run efficiently and consistently. Water heaters work hard to provide warm baths, clean clothes, shiny pots, and pans for you. Therefore, you must keep it functioning at its peak condition.

If you want to maintain your water heater, you should start by keeping the gas and electric water heaters working efficiently. There are many common repairs, such as how to empty gas or electric water heater. It may also involve how to control the pressure relief valve and tank or pilot lamp. Yet if you are not securely working with gas or energy, contact an expert.

Furthermore, we will share with you some tips on how to maintain your water heater to avoid any issues. More often, you need a hot water technician to support it. However, take note that water heaters may depreciate over time. It only means that one day, it will lose its effectivity and you will need some replacements. These steps will only help you prolong its use.

How to Maintain Your Water Heater?

Have you been looking for someone who would help you with water heater maintenance or for your other repair? We know you’ve wanted to have answers, so we will give you some tips on water heater maintenance. These are easy steps, and you don’t have to be an expert in doing it.

  • Check Valve Stress. All gas and electric water heaters fit with a safety device called a temperature and pressure reduction valve, or short T&P tap. The relief 犀利士 valve opens and reduces the gas in case the tank over-pressurized. If the valve is not working correctly, the container can overpressure and burst.
  • Put the Thermostat setting to 120 degrees. You can use up to 5 percent in energy costs for every 10 degrees you lower the temperature. Therefore, you can reduce the risk of scalding.
  • Please have 2 feet of clearance around the appliance, unless stated otherwise in the manual.
  • Drain a few days a year, about a fifth of the tank to eliminate water and litter. Switch off the flow of cold water, hook up a garden hose onto the drain valve and pump into a bucket until the water is clear. If the water remains stagnant, open the water supply valve slightly to remove the excess mud and empty the tank. It also helps the machine run smoother.
  • Test the temperature-pressure relief annually by releasing it two or three times quickly. Keep an eye out for minor leakage from the valve after the check.
  • Examine the heater’s anode rod every three years by loosening and inserting the hex headpin.
  • Make sure to replace the rod if any of these circumstances happen:
    • Expose the core steel wire to more than 6 inches. 
    • There’s calcium covering the rod.
  • Insulate older devices with a fiberglass jacket to improve performance. Insulate the tubing with hot and cold water, too. To be reliable, please listen to the manual on your water heater.

What are the Different Water Heater Maintenance?

An annual tune-up to your machine and some daily TLC can enable you to see even more efficiency and performance from your water heaters. They say that nothing lasts forever, but it doesn’t mean that there’s no way to prolong its purpose. Anything, including water heater, can last for a long time for as long as you know how to do 犀利士 proper maintenance.

  • Annual Service – Annual service of the water heaters will conserve your water heater and prolong its life and performance.
  • Sediments Flushing – For tank water heaters, you want to remove the deposition of sediments from the tank at least once a year. In your tank, the residue will affect the quality of the hot water while also reducing performance. The sediment layer interferes with the capacity of the furnace to heat the water, allowing additional fuel to produce the same heat boost.
  • Lookout for Overheating – There’s no reservoir for tankless water heaters, and so there’s no opportunity to build up the soil. However, since the water heats in the tankless device via a series of pipes, limescale will grow on the tubes and product. Once again, it can reduce heater performance and drive up running costs.
  • Flush Tankless Water Heater – Using a mild acidic solution such as food-grade white vinegar flushing, the tankless water heater helps remove and dislodge the calcium and sediment particles in the device. You should attach your vinegar solution to the input valves of the tankless invention, as instructed by the supplier. Such water heaters may differ slightly between make and model, so contact a licensed plumber to do a qualified descale to keep your tankless device useful if you’re uncertain.
  • Change the Anode Rod – The anode rod is what they call as the ‘sacrificial’ in tank water heaters. Annually, you can check the state of your anode rod to ensure it’s always intact. You can do it quickly by loosening and extracting the hex headpin. The anode rod should be modified if the core steel is apparent by more than 6 inches, the rod is less than 1/2 inch thick, or the rod gets covered with limescale accumulation. The composition of your anode rod could also cause a rotten egg smell from your water heater tank.
  • Give Your Water Heater Space – Your water heater requires sufficient space and ventilation for efficient service. Proper alignment and safe communications are further essential factors. Mainly for gas water heaters, careful positioning of the ventilation is especially important because the ventilation enables the escape of gasses from the water heater, like potentially dangerous carbon monoxide. These issues can be difficult to get right in a DIY project. If you know that you can’t handle it, calling a skilled hot water technician to mount your water heater is your best option.

How to Flush Sediments Out of a Water Tank?

Each homeowner knows how important it is to clean the systems and equipment and keep them safe. However, many homeowners don’t realize that flushing a water heater every year will clear a sediment build-up from the tank’s bottom.

The flushing sediment will increase the longevity and efficacy of a water heater. Sediment can create a barrier between the water heater and water heating components, making it harder to heat the toilets, dishwashers, and laundry in your house. You can save time and heat the water faster by flushing the contaminants out of your water heater.

  1. Switch the Heater On. Switch off the power switch, if you have an electric water heater. Then, turn your thermostat to the setting “pilot.” It turns off the heating element in your water heater to allow the water to cool down. Remember that there should be no one in your household who should be using the water.
  2. Switch off your Cold Water Valve. Switch off the refrigerated water valve. Once cold water is on the pool, a water heater pushes hot water through your house and displaces the boiling water. You will empty the tank of water without the cold water flowing into your pool. Make sure not to miss this step so that you won’t end up with water moving continuously into the tub and drain, which might cost you a pretty penny on your water bill.
  3. Let the water cool. Don’t drain the scalding hot water. Instead, tet the tank cool after you turn off the heating elements. Patience is a must because it can take up to two hours, depending on the size of the heater tanks.
  4. Add a sink or garden hose on the side of the tank to the drain valve. Choose the drain valve on your water heater leg and add a tube to it. Make sure that the hose threads on, or you might end up with leakage when you clean the water heater tank.
  5. Place the hose end in a seat bucket or sink. Remember, don’t flood your house. Once you start draining the water heater, make sure the drain doesn’t leak.
  6. Turn on a faucet. Opening the valves across your home will avoid the development of a vacuum inside your pipes. Switch the “heat” setting on your drains, and let them go. You won’t see much water coming out of them because you shut the cold water switch off to your water heater so that there would be no warm water that diverts.
  7. Turn on the drain valve to start draining the tank. Switch the valve on gently using a flathead screwdriver, make sure there are no holes and the tub or pipe you empty the water into won’t overflow.
  8. After the water heater tank has done removing the liquid, shut off the drain valve. Then, cut the pipe, and turn on the cold water valve. Finally, switch back on the heating elements in the furnace. Turn off the drain valve, and remove the hose, to fill your tank again. Turn the cold water valve on and return to the position on the heating elements.

Final Words

When you improve your water heater maintenance, it will provide you with higher efficiency, improved work, and lower operating costs. Regular water heater maintenance can even help you save money on the long-term costs of repairing the water heater. Should you detect strange smells emerging from your hot water tank, don’t hesitate to talk to your local water heater company.

Do you need more details on water heater maintenance and why yours is not functioning well? Quality Water Heater Services can help you anything about water heater installation, repair, and maintenance. If your water heater stopped working, you can get it repaired or replaced with us. Give us a call today. Our online requesting for support for any questions about water heater services.

Thank You

We will get back to you as soon as we read your message!